

On this page▼
- Nitro-X7 vs MagnaCut at a glance
- What Nitro-X7 and MagnaCut are
- What the nitrogen in Nitro-X7 does
- What has been published about each steel
- Hardness: close on paper
- Who uses Nitro-X7
- Price and availability: what Drop Beacon's catalogue shows
- Nitro-X7 or MagnaCut: which should you buy
- Is Nitro-X7 better than MagnaCut?
- Has Nitro-X7 been tested?
- What is Nitro-X7 steel?
- Which knives use Nitro-X7?
- Six knives in Nitro-X7 and MagnaCut, with live prices
- Related steel comparisons
- Sources
Drop Beacon may earn a commission when you buy through affiliate links on this page — at no extra cost to you. Full disclosure.
Short answer: Which is better, Nitro-X7 or MagnaCut? Nobody can say yet from published figures. MagnaCut's toughness, edge retention and salt-spray results are public, published by the company that sells it and by the metallurgist who designed it. For Nitro-X7, a search on 17 November 2026 found no published test figures, only claims from the mill and from the companies that make and sell knives in it.
That is a statement about what has been published, not about the steel. The mill says it has run cutting tests of its own, and it gives no result figures. So this article does not rank the two steels on any property. It sets out what can be sourced: what each steel is, who makes it, how hard makers run it, which knives use it, and what is in stock at what price.
The search was one day's work. Readers who know of a published test of Nitro-X7 with figures are invited to post it in the discussion below, so that this article can be updated.
Two terms used below. HRC is the Rockwell C hardness scale, where a higher number means a harder blade (how hardness affects a knife). CATRA is a machine test that measures how much abrasive card a blade cuts before it goes dull.
Nitro-X7 vs MagnaCut at a glance
| Nitro-X7 | MagnaCut | |
|---|---|---|
| Type | Stainless, conventionally melted, with added nitrogen | Stainless powder steel |
| Who makes it | Buderus Edelstahl (GMH Gruppe), Germany | Designed by Larrin Thomas, sold by Niagara Specialty Metals |
| Introduced | 2024 | 2021 |
| Carbon | 0.7% | 1.15% |
| Chromium | 15.3% | 10.7% |
| Vanadium | 0.12% | 4% |
| Nitrogen | 0.16% | 0.2% |
| Hardness as listed | 59 to 63 HRC, depending on the knife | Datasheet aim of 60 to 63 HRC |
| Edge retention | No published figure found | 135% of 440C in a CATRA test |
| Toughness | No published figure found | 38 ft-lbs at 62.5 HRC |
| Rust | No published figure found | No rust spots after 72 hours of 1% salt spray |
| Listings tracked | 47 from 7 sellers | About 7,400 from 148 makers and stores |
| In stock | 23 | About 2,400 |
| In-stock prices | $61.73 to $146.69 | From $39.99; median $275 |
| First seen in the last 90 days | 4 | About 900 |
Listing figures are from Drop Beacon's catalogue on 17 November 2026. MagnaCut's test figures come from its seller's data sheet and its designer's article. Where the table says no published figure was found, none was found in a search on that date.
What Nitro-X7 and MagnaCut are
Nitro-X7 is a stainless knife steel from Buderus Edelstahl of Wetzlar, Germany, part of GMH Gruppe. GMH's strip-steel page lists it as material X70CrMoVN15 and gives a typical analysis of 0.7% carbon, 15.3% chromium, 0.60% molybdenum, 0.12% vanadium and 0.16% nitrogen. The page places it in the Nitro series, which it describes as conventionally melted knife steels with a targeted nitrogen addition. Conventionally melted means the steel is cast as an ingot, not made from powder. The page describes Nitro-X7 as combining the high carbon content of the mill's Nitro-V with the carbide- and nitride-forming elements of its Nitro-B. Knife Steel Nerds lists it as a 2024 steel. Knife Steel Nerds also reported in December 2025 that Buderus's own steelworks had been shut down and that the Nitro grades continue as hot rolled strip, so this article does not say where the steel is melted.
MagnaCut is a stainless powder steel designed for knives by Dr. Larrin Thomas, the metallurgist who writes Knife Steel Nerds, and sold by Niagara Specialty Metals since April 2021. Its data sheet lists 1.15% carbon, 10.7% chromium, 4% vanadium, 2% molybdenum, 2% niobium and 0.2% nitrogen. Carbides are the hard particles in a steel that resist wear. MagnaCut was designed to contain no chromium carbides, only small vanadium and niobium ones. A powder steel is made from atomised powder, which keeps those particles small.
The two recipes differ in route and in content. Nitro-X7's listed analysis has less carbon, more chromium, far less vanadium and no niobium, and both steels contain a small amount of nitrogen. A recipe is not a test result, and nothing in this section says how either steel performs.
What the nitrogen in Nitro-X7 does
GMH Gruppe's page says nitrogen forms nitrides in steel, which raises hardness and improves corrosion resistance. That is the mill's general statement about nitrogen, not a test of Nitro-X7.
Knife Steel Nerds makes a similar general point in its article on nitrogen-alloyed knife steels: nitrogen raises the hardness of steel much as carbon does, and it is less likely than carbon to form a compound with chromium. The same article says nitrogen tends to float out of liquid steel, which limits the amount that can be added to about 0.2%.
Nitrogen is not unique to Nitro-X7 in this comparison. MagnaCut's data sheet lists 0.2% nitrogen, against 0.16% for Nitro-X7. Thomas wrote of his own steel that nitrogen can slow the coarsening of carbides in powder steels, and that he did not know for sure whether 0.2% was enough to make a measurable difference.
What has been published about each steel
MagnaCut. Two sources publish figures, and both have a stake in the steel: Niagara sells it and Thomas designed it.
- Toughness is a steel's resistance to chipping and breaking. The data sheet lists 38 ft-lbs at 62.5 HRC.
- Edge retention is how long a blade keeps cutting before it needs sharpening. The data sheet lists 135% of the reference steel 440C in a CATRA test at 62.5 HRC.
- Rust: the data sheet's chart shows no rust spots on MagnaCut after 72 hours of 1% saltwater spray, and Thomas reports no visible corrosion on the steel after 72 hours in his own 1% saltwater test.
Nitro-X7. A search on 17 November 2026 found claims, and no published test figures.
- The mill. GMH's page says initial tests with a knife at 63.3 HRC showed "very good edge stability after cutting tests on staples, hardwood and rope". It gives no result figures and no further detail of the tests, so the claim cannot be set beside MagnaCut's numbers. The only figure in it is the hardness of the test knife.
- Civivi. Its product picture for the Vyrent lists better edge retention, enhanced durability and superior corrosion resistance under a line that reads Upgraded from Nitro-V, so the comparison it makes is with Nitro-V. Its press release of 19 August 2026 calls Nitro-X7 newly developed and makes similar claims. Neither gives a test figure.
- Real Steel and DLT Trading. Real Steel's listing for the G-Drop says the steel enhances edge retention and corrosion resistance. DLT Trading, a dealer, describes excellent edge retention in its listings for the Demko AD20I Slim and the Reate Horizon X. None gives a test figure.
- Knife Steel Nerds. Its site search returns two articles that mention Nitro-X7. Neither reports a test of it.
Some pages could not be read and were not used. The steel's page on buderus-steel.com returned not found, and two forum threads about the steel could not be opened.
Hardness: close on paper
Makers list Nitro-X7 knives between 59 and 63 HRC.
- Civivi lists 60 to 62 HRC on the black Vyrent and 61 to 63 HRC on the silver one, on its product pictures and in its listings. Its press release gives 60 to 63 HRC.
- White Mountain Knives lists the Real Steel G-Drop at 59 to 61 HRC.
- The mill's own test knife was 63.3 HRC.
MagnaCut's data sheet aims for 60 to 63 HRC, so on paper the two overlap. The listed figure varies from knife to knife, and Civivi lists two different ranges for two versions of one model. Hardness is also only one input: a hardness figure is not a measure of edge retention, toughness or rust resistance.
Who uses Nitro-X7
Four makers named in the sources above use it: Civivi, Demko, Real Steel and Reate. Civivi's product picture calls the Vyrent its first Nitro-X7 blade. Drop Beacon's catalogue also carries one Linder knife in the steel, listed by a dealer. The models below are the ones in the catalogue on 17 November 2026.
- Civivi: the Vyrent, and the Estoc, first seen in the catalogue on 9 October 2026.
- Demko: the AD20I Slim, listed with clip point and shark foot blades.
- Real Steel: the G-Drop folder and the Trickster, a full-tang hunting knife.
- Reate: the Horizon-X, listed with drop point and tanto blades.
- Linder: the EVO-X Super Edge 7, a sheath knife with a 4.5-inch blade.
Price and availability: what Drop Beacon's catalogue shows
These figures are from Drop Beacon's catalogue on 17 November 2026. A listing is one knife at one store, so the same knife at three stores counts three times.
- Nitro-X7: 47 listings from 7 sellers and 5 makers. Demko and Reate have 16 each, Civivi 11, Real Steel 3 and Linder 1. 23 are in stock: 12 Reate, 8 Civivi, 2 Real Steel and 1 Linder. No Demko listing is in stock. In-stock prices run from $61.73 to $146.69, and 22 of the 23 are under $100. The lowest in-stock price is $61.73, for the black Civivi Vyrent, at Civivi's own store and at White Mountain Knives. The Demko AD20I Slim is listed at $450 to $650 and is sold out at all three sellers that list it.
- When the Nitro-X7 listings were first seen. Drop Beacon's records begin on 1 March 2026. The first Nitro-X7 listing, the Real Steel G-Drop, was seen on 9 March. The Demko AD20I Slim followed on 27 March, the Linder knife on 3 May, the Civivi Vyrent on 3 August and the Reate Horizon-X on 17 August. Four listings were first seen in the last 90 days: the Real Steel Trickster on 3 September, the shark foot Demko on 23 September and two Civivi Estoc listings on 9 October.
- MagnaCut: about 7,400 listings from 148 makers and stores. About 2,400 are in stock. In-stock prices start at $39.99, for a Kizer keychain knife, and the median in-stock price is $275. About 600 in-stock listings are under $200 and 16 are under $100. MagnaCut listings go back to the first day of Drop Beacon's records, and about 900 were first seen in the last 90 days.
The 90-day counts leave out Blade HQ, whose listings all carry the same load date in the catalogue.
Price is the clearest difference the catalogue shows. The median in-stock Nitro-X7 listing is $92, against $275 for MagnaCut. Choice is the other: MagnaCut has about a hundred times as many listings in stock. Both are facts about the knives on sale, not measures of either steel.
Browse Nitro-X7 knives or browse MagnaCut knives.
Nitro-X7 or MagnaCut: which should you buy
The choice turns on proof and on what is in stock, not on a claim that one steel outperforms the other.
Choose MagnaCut if you want a steel whose toughness, edge retention and rust results are published today, or you want a wide choice. About 2,400 listings are in stock from 148 makers and stores.
Choose Nitro-X7 if you are happy to be early on a new steel and to take the word of its mill and its makers for now, and one of the knives in stock suits you. On 17 November those were the Civivi Vyrent, the Real Steel G-Drop and Trickster, the Reate Horizon-X and the Linder EVO-X Super Edge 7, at $61.73 to $146.69.
For more on MagnaCut itself, see Is MagnaCut steel worth it? and MagnaMax vs MagnaCut.
Is Nitro-X7 better than MagnaCut?
Nobody can say yet from published figures. MagnaCut's toughness, edge retention and salt-spray results are published by its seller and its designer. For Nitro-X7, a search on 17 November 2026 found no published test figures, only claims from the mill and from the companies that make and sell knives in it. Until figures are published, ranking the two on any property would be a guess.
Has Nitro-X7 been tested?
The mill says it has. GMH Gruppe's page describes cutting tests on staples, hardwood and rope with a knife at 63.3 HRC. It gives no result figures, and no published test with figures was found on 17 November 2026. That search was one day's work, and two forum threads about the steel could not be opened.
What is Nitro-X7 steel?
Nitro-X7 is a stainless knife steel from Buderus Edelstahl, part of GMH Gruppe, listed as material X70CrMoVN15. Its typical analysis is 0.7% carbon, 15.3% chromium, 0.60% molybdenum, 0.12% vanadium and 0.16% nitrogen. The mill describes it as conventionally melted, so it is not a powder steel, and Knife Steel Nerds lists it as a 2024 steel.
Which knives use Nitro-X7?
In Drop Beacon's catalogue on 17 November 2026: the Civivi Vyrent and Estoc, the Demko AD20I Slim, the Real Steel G-Drop and Trickster, the Reate Horizon-X and the Linder EVO-X Super Edge 7. 23 of the 47 listings were in stock, and none of the Demko listings was.
Six knives in Nitro-X7 and MagnaCut, with live prices
Live prices from the stores Drop Beacon tracks. Three Nitro-X7 knives from three makers first, then three MagnaCut knives at different prices.

White Mountain Knives
Civivi Vyrent Folding Knife Black G-10 Handle Nitro-X7 Drop Point Plain Edge Black Stonewash Finish 3.48" C25037-1From $61.73 at White Mountain Knives


White Mountain Knives
Reate Horizon-X Folding Knife Black Glass FatCarbon Handle 3.2" Stonewash Nitro-X7 Drop Point HX-BK-SW-DPFrom $92 at White Mountain Knives

Blade HQ
Bestech Knives Dundee Liner Lock MagnaCut Knife Black G-10 (3.5" Gray PVD)From $107.95 at Blade HQ

Blade HQ
Kershaw Bel Air MagnaCut DuraLock Knife Gray Aluminum (3" Black SW) 6105From $159.95 at Blade HQ
Related steel comparisons
- Is MagnaCut steel worth it?
- MagnaMax vs MagnaCut: full data and a verdict
- S110V vs MagnaCut, with MagnaMax
- M4 vs MagnaCut
- Maxamet vs MagnaCut
- S35VN vs M390 vs MagnaCut
- Civivi vs Real Steel
Sources
- GMH Gruppe: strip steel, including the Nitro series
- Knife Steel Nerds (Larrin Thomas): What Could be Next for Knife Steel?, Buderus Steel Mill Closing? Yes, But Also No, nitrogen-alloyed knife steels and CPM MagnaCut
- Niagara Specialty Metals: CPM MagnaCut data sheet
- Civivi: press release on the Vyrent, carried by The Shooting Wire, and its product pictures and listings for the Vyrent
- Dealer listings: White Mountain Knives, Real Steel G-Drop, DLT Trading, Demko AD20I Slim and DLT Trading, Reate Horizon X
- Real Steel's listings for the G-Drop and Trickster
- Drop Beacon's catalogue of tracked listings, 17 November 2026
Last updated: 17 November 2026.
🔥 Trending This Week
- 1

Spyderco Charisma Folding Knife Red FRN Handle CTS-BD1N Plain Edge Satin Finish C259PRD
White Mountain Knives
$97.50
- 2

Control Series
GeeOne
$249.90
- 3

Benchmade Mini Adira 18065S Folding Knife – 3.21" Stonewash CPM-MagnaCut Drop Point Partially Serrated Blade, Depth Blue Grivory Handle, AXIS Lock
Blade City
$225.00
- 4

Pro-Tech Duke 2 Automatic Knife Nautical Aluminum Handle Stonewash 2.65" 20CV Drop Point DUKE2101-20CV-NAUTICAL
White Mountain Knives
$250.00
- 5

QSP Penguin Folding Knife Christmas Glow-in-the-Dark Resin Handle 14C28N Sheepsfoot Plain Edge Christmas Edition QS130GL-H1 MX
White Mountain Knives
$89.00
Sign in to leave a comment.
You might also like

S110V vs MagnaCut (and MagnaMax): Which Steel to Buy
MagnaCut is the better buy for most people. S110V holds an edge longer but chips more easily, and MagnaMax matches S110V's edge life with more toughness. Test data, prices and stock.

M4 vs MagnaCut: Which Knife Steel to Buy, and for Whom
MagnaCut is the better buy for most people: it is stainless and tested tougher than CPM-M4. M4 holds an edge slightly longer but needs rust care. Test data, prices and stock.

Maxamet vs MagnaCut: Which Knife Steel to Buy, and for Whom
MagnaCut is the better buy for most people. Maxamet holds an edge longer, but it can rust, it is slow to sharpen and every tracked Maxamet knife is a Spyderco. Test data, prices and stock.

MagnaMax vs Maxamet: Which Knife Steel to Buy, and for Whom
MagnaMax is the better buy for most people: stainless, likely tougher and sold by eight makers. Maxamet still holds an edge longer, but it rusts and every tracked Maxamet knife is a Spyderco.
