1 / 38

Screw-It Balls V2

Name: Screw-It Balls V2
Brand: Fellhoelter

$50.00–$110.00

Pens & Writing

Availability needs checking

Last observed: 2026-06-03 11:01 UTC. Check the selected seller for current availability.

First listed 8mo ago

Find it on eBay

In stock now

Screw-It Balls V2 is sold out — here are similar picks you can buy today.

Rick Hinderer KnivesInvestigator Pen- Stainless Steel DLC/PVD Finishes

$70.00

OlightOlight O’Pen 3 Black – 120 Lumens, White, Red & Green Laser, Built-in Li-Po, USB-C Rechargeable, Bolt-Action Ballpoint Pen

$79.97

Novel CarryThe Axial - Titanium Bolt-Action Fidget Pen

$99.99

GiantMouseTi2 Design x GiantMouse TechLiner Pen

$125.00

About Screw-It Balls V2

Note: This is just the Ball!

Here it is, the driver I use to assemble all of the products here at the Fellhoelter shop.
Steven Kelly and I set out to make a driver that was comfortable, dealt with the flaws I perceive in other custom drivers, is fun, and spins for a long time, if you are one of those twitchy, fidgeting types.
One of my biggest complaints with the crop of custom drivers that I have come across is visibility.
They all use the short driver bits, and are generally larger in diameter.
(Mine are 3/8″ in diameter or about 9.5mm)
The short bits cause at least 2 problems, for ME, maybe not for you…
1, It blocks the visibility of small screws, and makes them awkward to use.
2, they don’t reach in to tight places. A common place that gets me are my low ride pocket clips. Many of the bits do not reach in them. And if they do, they block the whole hole, so you can’t see what is going on.

The Original Screw-It Drivers used 2″ long power driver bits.
Well, we had some people stick normal 1/4" drive bit in there and get them stuck.
I have since discovered some Wera bits, that have an extended nose, but are the more common length of bit.
The best of both worlds.
They cost more, but I love them, and think you will too.
I’ll even provide you with T6, 8, 10, and 15 Torx bits from Wera, one of the best in the business.
These are the most common sizes used on knives, and the stuff I make.
More bits can be bought at any hardware store, and less common bits like the Torx are found at industrial supply houses like McMaster-Carr and MSC.
Of course Google finds them too.
The long, power bits still work in these as well, of course, but you will find that they do not seat as deeply in to the stem.

The ball uses a stainless bearings.
You can remove the ball for cleaning, but not the bearing from the ball…
You can also blow air or brake cleaner in the hole in the ball, which blows through the bearing, and keeps it spinning at max speed.
If you reach out to us, we can even build you a ball with a ceramic bearing instead, at an even more premium price!

Right now, I am getting about 30 seconds to 1 minute spins out of a clean bearing, and a copper ball.
The Titanium doesn’t spin as long, but still spins for a long time.

The bits are held in place by a magnet, so they are very easy to change from one size to the next.
If you are lazy like me though, you’ll just want several drivers, in different materials, for each size.
Then, you can tell at a glance what is what, and never slow down…

Now shipping with packaging that doubles as a display / bench holder.
This display will hold the driver, quite a few bits, and even my pens!

We have many of these done already, and some that need completion.
So, I am going to call this a pre-order.
If you are one of the first to order, yours will ship next week, once we run out of completed drivers, we'll ship according to order number, Though everything should ship by the 2nd week of February.
Remember, this is JUST the Ball. You still need a stem to complete the driver.

From the buyer's guide

Best EDC Pens of 2026

See how this pen compares against the year's most-recommended EDC writing instruments.

Availability history: Among 356 drops tracked for Fellhoelter, 88% have a recorded unavailability event. These observations do not verify completed sales.

Compare configurations and sellers

Choose the same version, finish, size and included parts to compare prices. Prices exclude shipping, tax and conditional discounts.

Configuration

Fellhoelter$50.00 USD

Screw-It Balls V2 · Titanium-Standard

New · Availability needs checking

Last observed: 6/3/2026, 11:01:19 AM UTC

Screw-It Balls V2

In stock now

About Screw-It Balls V2

Note: This is just the Ball!

Now shipping with packaging that doubles as a display / bench holder.This display will hold the driver, quite a few bits, and even my pens!

Best EDC Pens of 2026

Compare configurations and sellers

B/S/T Listings

Price history

Frequently asked questions

How much does the Screw-It Balls V2 cost?

What does the recorded availability history for Fellhoelter show?

Screw-It Balls V2

In stock now

About Screw-It Balls V2

Note: This is just the Ball!

Now shipping with packaging that doubles as a display / bench holder.This display will hold the driver, quite a few bits, and even my pens!

Best EDC Pens of 2026

Compare configurations and sellers

B/S/T Listings

Price history

Frequently asked questions

How much does the Screw-It Balls V2 cost?

What does the recorded availability history for Fellhoelter show?

Now shipping with packaging that doubles as a display / bench holder.
This display will hold the driver, quite a few bits, and even my pens!

Now shipping with packaging that doubles as a display / bench holder.
This display will hold the driver, quite a few bits, and even my pens!